Add esp32.wake_on_ulp() to give access to esp_sleep_enable_ulp_wakeup(),
which is needed to allow the ULP co-processor to wake the main CPU from
deep sleep.
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
Rework the ADC implementation to follow the improved ADC/ADCBlock API.
This adds support for calibrated voltage readings and the ADC2 block. The
ADC API is backwards compatible with what it was before this change.
Resolves#6219.
This commit refactors machine.PWM and creates extmod/machine_pwm.c. The
esp8266, esp32 and rp2 ports all use this and provide implementations of
the required PWM functionality. This helps to reduce code duplication and
keep the same Python API across ports.
This commit does not make any functional changes.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
Improvements made:
- PSRAM support for S2
- partition definition for 16MiB flash
- correct ADC and DAC pins
- correct GPIO and IRQ pins
- S3 components in CMakeLists
Based on original commit made by Seon Rozenblum aka @UnexpectedMaker.
Signed-off-by: Damien George <damien@micropython.org>
This commit fixes two issues on the esp32:
- it enables machine.soft_reset() to be called in main.py;
- it enables machine.reset_cause() to correctly identify a soft reset.
The former is useful in that it enables soft resets in applications that
are started at boot time. The support is patterned after the stm32 port.
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
The code previously called rtc_get_reset_reason which is a "raw" reset
cause. The ESP-IDF massages that for the proper reset cause available from
esp_reset_reason.
Fixes issue #5134.
This provides a more consistent C-level API to raise exceptions, ie moving
away from nlr_raise towards mp_raise_XXX. It also reduces code size by a
small amount on some ports.
This commit adds support for a second supported hash (currently set to the
4.0-beta1 tag). When this hash is detected, the relevant changes are
applied.
This allows to start using v4 features (e.g. BLE with Nimble), and also
start doing testing, while still supporting the original, stable, v3.3 IDF.
Note: this feature is experimental, not well tested, and network.LAN and
network.PPP are currently unsupported.
This adds support for SD cards using the ESP32's built-in hardware SD/MMC
host controller, over either the SDIO bus or SPI. The class is available
as machine.SDCard and using it can be as simple as:
uos.mount(machine.SDCard(), '/sd')
This commit is a combination of 216 commits from the initial stages of
development of this port, up to and including the point where the code was
moved to the ports/esp32 directory. These commits were mostly concerned
with setting up the build system and getting a reliable port working with
basic features. The following is a digest of the original commits in their
original order (most recent listed first), grouped where possible per
author. The list is here to give credit for the work and provide some
level of traceability and accountability. For the full history of
development please consult the original repository.
All code is MIT licensed and the relevant copyright holders are listed in
the comment-header of each file.
Damien George <damien.p.george@gmail.com>
esp32: Update to latest ESP IDF.
esp32: Update module symlinks now that code lives under the ports dir.
esp32: Update to compile with new ports/esp32 directory structure.
esp32: Move it to the ports/ directory.
esp32/machine_uart: Don't save baudrate but compute it instead.
esp32/modsocket: Add socket.readinto() method.
esp32/modesp: Add esp.gpio_matrix_in and esp.gpio_matrix_out functions.
esp32/machine_uart: Wait for all data to be tx'd before changing config.
NyxCode <moritz.bischof1@gmail.com>
esp32: Add note to README.md about updating the submodules of ESP IDF.
Anthony Briggs <anthony.briggs@gmail.com>
esp32: Update README.md installation and flashing instructions.
Javier Candeira <javier@candeira.com>
esp32: Raise error when setting input-only pin to output.
With help from Adrian Smith (fon@thefon.net)
Javier Candeira <javier@candeira.com>
esp32: Replace exception raising with corresponding mp_raise_XXX funcs.
Tisham Dhar <whatnickd@gmail.com>
esp32: Add some specific notes about building on Windows using WSL.
Ben Gamari <ben@smart-cactus.org>
esp32: Provide machine.Signal class.
Damien George <damien.p.george@gmail.com>
esp32/modnetwork: Implement AP version of network.isconnected().
Eric Poulsen <eric@zyxod.com>
esp32/README.md: Add note about btree submodule initialization.
Damien George <damien.p.george@gmail.com>
esp32: Make firmware.bin start at 0x1000 to allow flash size autodetect.
esp32: Changes to follow latest version of upstream uPy.
esp32/Makefile: Separate ESP-specific inc dirs to avoid header clashes.
esp32: Enable "btree" database module.
esp32: Update to latest ESP IDF.
Roosted7 <thomasroos@live.nl>
esp32: Update to latest ESP-IDF.
Alex King <alex_w_king@yahoo.com>
esp32/machine_timer: Add support for esp32 hardware timer.
Code lineage:
Timer() is based loosely on the version in esp8266, although the
implementation is differs significantly because of the change in
the underlying platform.
Damien George <damien.p.george@gmail.com>
esp32/machine_uart: Increase UART TX buffer size to 64.
esp32/modules: Update dht symlink.
esp32/mpconfigport.h: Enable utimeq module, needed for uasyncio.
esp32: Changes to follow latest version of upstream uPy.
esp32: Update to latest ESP-IDF.
esp32/machine_uart: Add uart.any() method.
esp32/machine_uart: Uninstall the UART driver before installing it.
Thomas Roos <mail@thomasroos.nl>
esp32: Update to latest ESP-IDF.
Eric Poulsen <eric@zyxod.com>
esp32/modsocket: Make read/write return None when in non-blocking mode.
esp32/modsocket.c: Fix send/sendto/write for non-blocking sockets.
Odd Stråbø <oddstr13@openshell.no>
esp32: Initial working implementation of machine.UART.
Code lineage (as seen by previous commits): I copied the ESP8266 code,
renamed pyb -> machine, and used esp-idf as a reference while implementing
minimal functionality. I provide all of my changes under the MIT license.
Odd Stråbø <oddstr13@openshell.no>
esp32/machine_uart: Rename pyb to machine.
esp32: Copy machine_uart.c from esp8266 port.
Damien George <damien.p.george@gmail.com>
esp32/moduos: Add uos.ilistdir() function.
esp32: Mount filesystem at the root of the VFS, following esp8266.
Andy Valencia <vandyswa@gmail.com>
esp32: Add hardware SHA1/SHA256 support via mbedtls API.
Code lineage: a copy of extmod/moduhashlib with the API invocation details
edited. Total derivative work.
Andy Valencia <vandyswa@gmail.com>
esp32: Add PWM support via machine.PWM class.
Code lineage:
I started by copying the esp8266 machine_pwm.c. I used information from the
ESP32 Technical Reference Manual, the esp-idf documentation, and the SDK's
sample ledc example code (but I did not copy that code, just studied it to
understand the SDK's API for PWM). So aside from the code copied from the
esp8266 PWM support, everything else you see is just new code I wrote.
I wasn't an employee of anybody when I wrote it, and I wrote it with the
understanding and intention that it's simply a derivative work of the
existing micropython code. I freely and willingly contribute it to the
project and intend that it not change the legal status of the micropython
code base in any way, even if it is included in that base in whole or part.
Damien George <damien.p.george@gmail.com>
esp32/modules: Add symlinks for upysh and upip.
Eric Poulsen <eric@zyxod.com>
esp32/modmachine: Add unique_id() function to machine module.
Damien George <damien.p.george@gmail.com>
esp32: Change dac_out_voltage to dac_output_voltage for new IDF API.
esp32: Update esp32.custom_common.ld to align with changes in ESP IDF.
Eric Poulsen <eric@zyxod.com>
esp32: Update to latest ESP IDF.
Damien George <damien.p.george@gmail.com>
esp32/modsocket: When resolving IP addr handle the case of host=''.
esp32: Update to latest ESP IDF.
Eric Poulsen <eric@zyxod.com>
esp32/Makefile: Change default FLASH_MODE to dio for WROOM-32 module.
esp32: Move FAT FS to start at 0x200000 and increase size to 2MiB.
Damien George <damien.p.george@gmail.com>
esp32: Remove enable_irq/disable_irq and use ATOMIC_SECTION instead.
esp32/mpconfigport.h: Provide ATOMIC_SECTION macros.
esp32/main: Restart the MCU if there is a failed NLR jump.
Daniel Campora <daniel@pycom.io>
esp32: Enable threading; be sure to exit GIL when a thread will block.
esp32: Trace the registers when doing a gc collect. Also make it thread ready.
esp32: Add threading implementation, disabled for the time being.
Damien George <damien.p.george@gmail.com>
esp32: Update to latest ESP IDF.
esp32/uart: Use high-level function to install UART0 RX ISR handler.
esp32/Makefile: Make FreeRTOS private include dir really private.
Eric Poulsen <eric@zyxod.com>
esp32: Add support for hardware SPI peripheral (block 1 and 2).
Sergio Conde Gómez <skgsergio@gmail.com>
esp32/modules/inisetup.py: Mount filesystem at /flash like ESP8266
Damien George <damien.p.george@gmail.com>
esp32: Convert to use core-provided KeyboardInterrupt exception.
esp32: Pump the event loop while waiting for rx-chr or delay_ms.
esp32: Implement Pin.irq() using "soft" scheduled interrupts.
esp32: Update to latest ESP IDF version.
Eric Poulsen <eric@zyxod.com>
esp32/README: Add troubleshooting section to the end.
tyggerjai <tyggerjai@gmail.com>
esp32: Add support for WS2812 and APA106 RGB LEDs.
Damien George <damien.p.george@gmail.com>
esp32: Add makeimg.py script to build full firmware; use it in Makefile.
esp32/modsocket: Make socket.read return when socket closes.
esp32/modsocket: Initialise the timeout on an accepted socket.
esp32/mphalport: Provide proper implementations of disable_/enable_irq.
esp32/modmachine: Add disable_irq/enable_irq functions.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: add comment explaining timeout behaviour
esp32/modsocket.c: clean up send methods for retries too
esp32/modsocket.c: sockets always nonblocking, accept timeout in modsocket
esp32: Update to latest ESP IDF version.
esp32/modsocket.c: remove MSG_PEEK workaround on select ioctl.
esp32/modsocket.c: Initialize tcp when modsocket loads.
Damien George <damien.p.george@gmail.com>
esp32/main: Bump heap size from 64k to 96k.
esp32/modutime: Add time.time() function.
esp32/modsocket: Convert lwip errnos to uPy ones.
esp32/modules: Provide symlink to ds18x20 module.
esp32: Add support for onewire protocol via OneWire module.
esp32: Add support for DHT11 and DHT22 sensors.
esp32/mphalport: Improve delay and ticks functions.
esp32: Update to latest ESP IDF.
esp32/modules: Provide symlink to urequests from micropython-lib.
esp32: Populate sys.path.
Nick Moore <nick@zoic.org>
esp32/machine_dac.c: implement DAC pins as well
esp32/machine_adc.c: also machine.ADC
esp32/machine_touchpad.c: add support for touchpad
Damien George <damien.p.george@gmail.com>
esp32/README: Add hint about using GNUmakefile on case-insensitive FS.
esp32/mpconfigport.h: Enable maximum speed software SPI.
esp32: Provide improved version of mp_hal_delay_us_fast.
esp32/mpconfigport.h: Enable MICROPY_PY_BUILTINS_POW3 option.
esp32: Update to latest ESP IDF.
esp32: Convert to use new oofatfs library and generic VFS sub-system.
esp32: Enable help('modules') to list builtin modules.
esp32: Convert to use new builtin help function.
Aaron Kelly <AaronKelly@email.com>
esp32/README: Add comment about ESP-IDF version
Damien George <damien.p.george@gmail.com>
esp32: Consistently use size_t instead of mp_uint_t.
esp32: Change "Micro Python" to "MicroPython" in license comments.
esp32/Makefile: Use -C argument to git instead of cd'ing.
esp32/help: Add section to help about using the network module.
esp32/README: Add section about configuring and using an ESP32 board.
esp32/README: Remove paragraph about buggy toolchain, it's now fixed.
esp32/modnetwork: Change network init logging from info to debug.
esp32/modnetwork: Don't start AP automatically when init'ing wifi.
esp32/modsocket: Implement socket.setsockopt, to support SO_REUSEADDR.
esp32: Update to latest ESP IDF.
esp32/sdkconfig.h: Remove unused CONFIG_ESPTOOLPY_xxx config settings.
esp32/modsocket: Add support for DGRAM and RAW, and sendto/recvfrom.
esp32/modsocket: Fix return value of "port" in socket.accept.
esp32/modsocket: Make socket.recv take exactly 2 args.
esp32: Enable ussl module, using mbedtls component from ESP IDF.
esp32/modsocket: Rename "socket" module to "usocket".
esp32/sdkconfig: Increase max number of open sockets from 4 to 8.
esp32/modsocket: Add error checking for creating and closing sockets.
esp32/modsocket: Use _r (re-entrant) versions of LWIP socket API funcs.
esp32/modsocket: Raise an exception if socket.connect did not succeed.
esp32/modsocket: Make socket.accept return a tuple: (client, addr).
esp32/modsocket: Use m_new_obj_with_finaliser instead of calloc.
esp32/Makefile: Add check for IDF version, and warn if not supported.
esp32/esp32.custom_common.ld: Update to follow changes in IDF.
esp32: Update to latest ESP IDF.
nubcore <x@nubcore.com>
esp32: add #define CONFIG_ESP32_WIFI_RX_BUFFER_NUM 25
Nick Moore <nick@zoic.org>
esp32/modsocket.c: add in sendall and makefile methods #10
esp32/modsocket.c: fixups for #10
esp32/modsocket.c: fix copyright, socket_recv gets param and exception
esp32/modnetwork.c: fix copyright, network.active param to bool
Damien George <damien.p.george@gmail.com>
esp32/modnetwork: Implement wlan.isconnected() method.
esp32/modnetwork: Add initial implementation of wlan.config().
esp32/modnetwork: Simplify event_handler messages.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: support for ioctl, settimeout, setblocking, getaddrinfo
Damien George <damien.p.george@gmail.com>
esp32/README: Add comment about FLASH_MODE being dio.
esp32: Update to latest ESP IDF.
esp32/modnetwork: Remove unnecessary indirection variable for scan list.
esp32/modnetwork: Check that STA is active before trying to scan.
esp32/mphalport: Replace portTICK_RATE_MS with portTICK_PERIOD_MS.
esp32/README: Add comment about using $(HOME) in makefile.
esp32/modnetwork: Use memset instead of bzero, the latter is deprecated.
esp32/modnetwork: Improve error handling when STA is connecting to AP.
esp32/Makefile: Use tab instead of spaces, and use shorter variable.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: AF_*, SOCK_* and IPPROTO_* constants
esp32/modsocket.c: socket.settimeout implementation
Damien George <damien.p.george@gmail.com>
esp32/Makefile: Update to latest ESP IDF.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: use mp streams for sockets
esp32: network.WLAN.ifconfig based on esp8266 version
esp32: Fix up exception handling
esp32: sketchy modsocket ... revisit this once modnetwork is sorted
esp32: First cut at modnetwork, manually rebased from prev. version
Damien George <damien.p.george@gmail.com>
esp32/help: Update help text.
esp32: Add info about Microbric Pty Ltd being the sponsor of this port.
esp32: Add README.md file.
esp32/mpconfigport.h: Add weak links to many of the builtin modules.
esp32: Enable soft implementation of machine.SPI class.
esp32/Makefile: Simplify APP_LD_ARGS by using OBJ variable.
esp32/Makefile: Reorganise Makefile and add some comments.
esp32/Makefile: Clean up CFLAGS for ESP IDF components.
esp32/Makefile: Tidy up names of ESP IDF components, to match dir name.
esp32/Makefile: Define and use ESPCOMP variable.
esp32: Update to latest ESP IDF.
esp32/main: Enable filesystem support.
esp32: Use custom ld script to ensure correct code get placed in iram.
esp32: Update to latest ESP IDF.
esp32/main: Pin the uPy task to core 0.
esp32: Update to use latest ESP IDF.
esp32: Disable boot-up scripts, spi_flash_erase_sector no longer works.
esp32: Add scripts to init and mount filesystem.
esp32: Enable frozen bytecode, with scripts stored in "modules/" dir.
esp32/modesp: Increase flash_user_start position to 1Mbyte.
esp32/Makefile: Add "erase" target for convenient erasure.
esp32/sdkconfig: Reorder config settings to put common things together.
esp32/sdkconfig: Change to use single core only.
esp32: Add esp module.
esp32/uart.c: Make sure uart ISR handler is all in iram.
esp32/main.c: Use ESP_TASK_PRIO_MIN + 1 for mp_task's priority.
esp32/Makefile: Use only bare-minimum flags when compiling .S files.
esp32/Makefile: Rename "firmware" to "application".
esp32: Update ESP IDF version.
esp32/Makefile: Add declarations to build bootloader and partitions.
esp32/Makefile: When deploying, write the application last.
esp32/Makefile: Use $(INC) variable instead of listing include dirs.
esp32/Makefile: Use locally built versions of freertos and newlib libs.
esp32: Add low-level uart handler with ISR and ringbuf for stdin.
esp32: Add machine.idle() function.
esp32: Add machine.I2C class.
esp32: Enable machine.time_pulse_us.
esp32: Add initial implementation of machine.Pin class.
esp32: Prepare main.c for using xTaskCreateStatic.
esp32: Clean up mphalport.h.
esp32: Add initial uos module.
esp32: Clean up mpconfigport.h, enable more features.
esp32: Use new reset function.
esp32: Update to latest ESP IDF.
esp32: Add idf-version target to Makefile, to track IDF commit.
esp32: Initial port to ESP32.
iabdalkader