architecture message inline with stdout for clarity.
* path.cc (is_symlink): Always reset file pointer to beginning on exit.
(readlink): Assume that file pointer is set to the beginning.
* mips.h (M_ACLR_OB, M_ASET_OB, M_CACHE_OB, M_CACHEE_OB, M_L_DOB)
(M_LB_A, M_LBE_OB, M_LBU_A, M_LBUE_OB, M_LD_A, M_LD_OB, M_LDC2_OB)
(M_LDL_OB, M_LDM_OB, M_LDP_OB, M_LDR_OB, M_LH_A, M_LHE_OB, M_LHU_A)
(M_LHUE_OB, M_LL_OB, M_LLD_OB, M_LLE_OB, M_LS_A, M_LW_A, M_LWE_OB)
(M_LWC0_A, M_LWC1_A, M_LWC2_A, M_LWC2_OB, M_LWC3_A, M_LWL_A, M_LWL_OB)
(M_LWLE_OB, M_LWM_OB, M_LWP_OB, M_LWR_A, M_LWR_OB, M_LWRE_OB, M_LWU_OB)
(M_PREF_OB, M_PREFE_OB, M_S_DOB, M_SAA_OB, M_SAAD_OB, M_SC_OB)
(M_SCD_OB, M_SCE_OB, M_SD_A, M_SD_OB, M_SDC2_OB, M_SDL_OB, M_SDM_OB)
(M_SDP_OB, M_SDR_OB, M_SB_A, M_SBE_OB, M_SH_A, M_SHE_OB, M_SW_A)
(M_SWE_OB, M_SWC0_A, M_SWC1_A, M_SWC2_A, M_SWC2_OB, M_SWC3_A, M_SWL_A)
(M_SWL_OB, M_SWLE_OB, M_SWM_OB, M_SWP_OB, M_SWR_A, M_SWR_OB, M_SWRE_OB)
(M_ULD, M_ULH, M_ULHU, M_ULW, M_USH, M_USW, M_USD): Delete.
(M_ULD_A, M_ULH_A, M_ULHU_A, M_ULW_A, M_USH_A, M_USW_A, M_USD_A):
Rename to...
(M_ULD_AB, M_ULH_AB, M_ULHU_AB, M_ULW_AB, M_USH_AB, M_USW_AB)
(M_USD_AB): ...these.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove o(b) macros. Move LD
and SD A(B) macros up.
* micromips-opc.c (micromips_opcodes): Likewise.
gas/
* config/tc-mips.c (gprel16_reloc_p): New function.
(macro_read_relocs): Assume BFD_RELOC_LO16 if all relocs are
BFD_RELOC_UNUSED.
(offset_high_part, small_offset_p): New functions.
(nacro): Use them. Remove *_OB and *_DOB cases. For single-
register load and store macros, handle the 16-bit offset case first.
If a 16-bit offset is not suitable for the instruction we're
generating, load it into the temporary register using
ADDRESS_ADDI_INSN. Make the M_LI_DD code fall through into the
M_L_DAB code once the address has been constructed. For double load
and store macros, again handle the 16-bit offset case first.
If the second register cannot be accessed from the same high
part as the first, load it into AT using ADDRESS_ADDI_INSN.
Fix the handling of LD in cases where the first register is the
same as the base. Also handle the case where the offset is
not 16 bits and the second register cannot be accessed from the
same high part as the first. For unaligned loads and stores,
fuse the offbits == 12 and old "ab" handling. Apply this handling
whenever the second offset needs a different high part from the first.
Construct the offset using ADDRESS_ADDI_INSN where possible,
for offbits == 16 as well as offbits == 12. Use offset_reloc
when constructing the individual loads and stores.
(mips_ip): Set up imm_expr, imm2_expr, offset_expr, imm_reloc
and offset_reloc before matching against a particular opcode.
Handle elided 'A' constants. Allow 'A' constants to use
relocation operators.
gas/testsuite/
* gas/mips/ldstla-32.d: Avoid "lui at,0x0" sequences for
truncated constants.
* gas/mips/ldstla-32-shared.d: Likewise.
* gas/mips/mcu.d: Use ADDIU in preference to LI+ADDU when adding
16-bit constants to the base.
* gas/mips/micromips@mcu.d: Likewise.
* gas/mips/micromips@cache.d: Likewise.
* gas/mips/micromips@pref.d: Likewise.
* gas/mips/micromips.d, gas/mips/micromips-insn32.d,
gas/mips/micromips-noinsn32.d, gas/mips/micromips-trap.d: Likewise.
Allow the full 16-bit offset range to be used for SB, LB and LBU in
USH and ULH sequences. Fix the expected output for LD and SD when
the two LW and SW offsets need different high parts.
* gas/mips/eva.s: Test PREFE with relocation operators.
* gas/mips/eva.d: Use ADDIU in preference to LI+ADDU for 16-bit
constants. Update after eva.s change.
* gas/mips/micromips@eva.d: Likewise.
* gas/mips/ld-reloc.s, gas/mips/ld-reloc.d, gas/mips/l_d-reloc.s,
gas/mips/l_d-reloc.d, gas/mips/ulw-reloc.s, gas/mips/ulw-reloc.d,
gas/mips/micromips@ulw-reloc.d, gas/mips/ulh-reloc.s,
gas/mips/ulh-reloc.d: New tests.
* gas/mips/mips.exp: Run them.
* mips.h: Remove documentation of "[" and "]". Update documentation
of "k" and the MDMX formats.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "Q" for the INSN_5400
MDMX-like instructions.
* mips-dis.c (print_insn_arg): Use "$f" rather than "$v" when
printing "Q" operands for INSN_5400 instructions.
gas/
* config/tc-mips.c (validate_mips_insn): Remove "[" and "]" handling.
(mips_ip): Likewise. Do not set is_mdmx for INSN_5400 instructions.
Check constraints on the VR5400 RZU.OB, SLL.OB and SRL.OB instructions.
gas/testsuite/
* gas/mips/vr5400-ill.s, gas/mips/vr5400-ill.l: New test.
* gas/mips/mips.exp: Run it.
* mips.h: Update documentation of "+s" and "+S".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "+s" for "cins32" and
"+S" for "cins".
* mips-dis.c (print_mips_arg): Update "+s" and "+S" comments.
Combine cases.
gas/
* config/tc-mips.c (mips_ip): Preserve the real bit number for "+p".
Require the msb to be <= 31 for "+s". Check that the size is <= 31
for both "+s" and "+S".
* mips.h: Document "+i".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "+i" rather than "a" for
"jalx".
* mips16-opc.c (mips16_opcodes): Likewise.
* micromips-opc.c (micromips_opcodes): Likewise.
* mips-dis.c (print_insn_args, print_mips16_insn_arg)
(print_insn_mips16): Handle "+i".
(print_insn_micromips): Likewise. Conditionally preserve the
ISA bit for "a" but not for "+i".
gas/
* config/tc-mips.c (validate_mips_insn, validate_micromips_insn):
(mips_ip, mips16_ip): Handle "+i".
* mips.h: Remove documentation of "+D" and "+T".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove "+D" and "+T" entries.
* micromips-opc.c (micromips_opcodes): Likewise.
* mips-dis.c (print_insn_args, print_insn_micromips): Remove "+D"
and "+T" handling. Check for a "0" suffix when deciding whether to
use coprocessor 0 names. In that case, also check for ",H" selectors.
gas/
* config/tc-mips.c (validate_mips_insn, validate_micromips_insn)
(mips_ip): Remove "+D" and "+T" handling.
gas/testsuite/
* gas/mips/lb.d, gas/mips/sb.d: Use coprocessor register names
for LWC0 and SWC0.
opcodes/
* s390-opc.c (J12_12, J24_24): New macros.
(INSTR_MII_UPI): Rename to INSTR_MII_UPP.
(MASK_MII_UPI): Rename to MASK_MII_UPP.
* s390-opc.txt: Rename MII_UPI to MII_UPP for bprp instruction.
include/elf/
* s390.h: Add new relocs R_390_PC12DBL, R_390_PLT12DBL,
R_390_PC24DBL, and R_390_PLT24DBL.
gas/testsuite/
* gas/s390/zarch-zEC12.s: Change bprp second operand and add
variants requiring relocations.
* gas/s390/zarch-zEC12.d: Likewise.
gas/
* config/tc-s390.c (md_gather_operands, md_apply_fix): Support new
relocs.
bfd/
* elf32-s390.c: Add new relocation definitions R_390_PC12DBL,
R_390_PLT12DBL, R_390_PC24DBL, and R_390_PLT24DBL.
(elf_s390_reloc_type_lookup, elf_s390_check_relocs)
(elf_s390_gc_sweep_hook, elf_s390_relocate_section): Support new
relocations.
* elf64-s390.c: See elf32-s390.c
* bfd-in2.h: Add new relocs to enum bfd_reloc_code_real.
* libbfd.h: Add new reloc strings.
Lite exit support.
* README: Add information about lite-exit.
* acconfig.h (_LITE_EXIT): New macro.
* configure.in (enable-lite-exit): New option.
(_LITE_EXIT): Define new macro.
* configure: Regenerated.
* newlib.hin (_LITE_EXIT): New macro.
* libc/stdlib/__atexit.c [_LITE_EXIT]: Add dummy explicit
reference to __call_exitprocs.
* libc/stdlib/cxa_atexit.c [_LITE_EXIT]: Make __register_exitproc a
weak reference.
* libc/stdlib/exit.c (exit)[_LITE_EXIT]: Remove TWS and weakly reference
__call_exitprocs.
Adjust the conditions for entering the aligned copy loop to
improve performance on mutually misaligned buffer copies.
2013-07-01 Will Newton <will.newton@linaro.org>
* libc/machine/arm/memcpy-armv7a.S: Adjust entry to
aligned loop to improve misaligned copy performance.
path without long path prefixing.
* wide_path.h (wide_path::wide_path): Allow extra bool parameter to
specify whether or not performing Windows long path prefixing.
* mips.h: Fix comment for "1": it is now STYPE rather than SHAMT.
Use "source" rather than "destination" for microMIPS "G".
gas/
* config/tc-mips.c (validate_mips_insn): Use STYPE rather than SHAMT.
(PTR_REG): Ditto.
(PTR_SIZE): Ditto.
(PTR_LOG_SIZE): Ditto.
(start): Use GEN_DWORD to replace the .dword of HeapBase,
__bss_start__, __bss_end__, FUNCTION(_fini), env and
CommandLine; when __ILP32__ is defined, set the stack base to
the top end of the 32-bit address space if the returned value
from the Angel API call is larger than or equal to 4 GiB.
Also carry out sanity check on the heap base; abort if the
base is larger than or equal to 4 GiB. Use other new
macros in the instructions that processes the argv arrays.
(StackBase): New lable; replace __stack_base__.
(__stack_base__): Set with StackBase or StackBase + 4.
* elfxx-mips.h (_bfd_mips_elf_get_synthetic_symtab): New
prototype.
* elf32-mips.c (elf_backend_plt_sym_val): Remove macro.
(bfd_elf32_get_synthetic_symtab): New macro.
* elfxx-mips.c (plt_entry): New structure.
(mips_elf_link_hash_entry): Add use_plt_entry member.
(mips_elf_link_hash_table): Rename plt_entry_size member to
plt_mips_entry_size. Add plt_comp_entry_size, plt_mips_offset,
plt_comp_offset, plt_got_index entries and plt_header_is_comp
members.
(STUB_LW_MICROMIPS, STUB_MOVE_MICROMIPS): New macros.
(STUB_LUI_MICROMIPS, STUB_JALR_MICROMIPS): Likewise.
(STUB_ORI_MICROMIPS, STUB_LI16U_MICROMIPS): Likewise.
(STUB_LI16S_MICROMIPS): Likewise.
(MICROMIPS_FUNCTION_STUB_NORMAL_SIZE): Likewise.
(MICROMIPS_FUNCTION_STUB_BIG_SIZE): Likewise.
(micromips_o32_exec_plt0_entry): New variable.
(mips16_o32_exec_plt_entry): Likewise.
(micromips_o32_exec_plt_entry): Likewise.
(mips_elf_link_hash_newfunc): Initialize use_plt_entry.
(mips_elf_output_extsym): Update to use gotplt_union's plist
member rather than offset.
(mips_elf_gotplt_index): Likewise. Remove the VxWorks
restriction. Use MIPS_ELF_GOT_SIZE to calculate GOT address.
(mips_elf_count_got_symbols): Update to use gotplt_union's plist
member rather than offset.
(mips_elf_calculate_relocation): Handle MIPS16/microMIPS PLT
entries.
(_bfd_mips_elf_create_dynamic_sections): Don't set PLT sizes
here.
(mips_elf_make_plt_record): New function.
(_bfd_mips_elf_check_relocs): Update comment. Record occurences
of JAL relocations that might need a PLT entry.
(_bfd_mips_elf_adjust_dynamic_symbol): Update to use
gotplt_union's plist member rather than offset. Set individual
PLT entry sizes here. Handle MIPS16/microMIPS PLT entries.
Don't set the symbol's value in the symbol table for PLT
references here. Don't set the PLT or PLT GOT section sizes
here.
(mips_elf_estimate_stub_size): Handle microMIPS stubs.
(mips_elf_allocate_lazy_stub): Likewise.
(mips_elf_lay_out_lazy_stubs): Likewise. Define a _MIPS_STUBS_
magic symbol.
(mips_elf_set_plt_sym_value): New function.
(_bfd_mips_elf_size_dynamic_sections): Set PLT header size and
PLT and PLT GOT section sizes here. Set the symbol values in
the symbol table for PLT references here. Handle microMIPS
annotation of the _PROCEDURE_LINKAGE_TABLE_ magic symbol.
(_bfd_mips_elf_finish_dynamic_symbol): Update to use
gotplt_union's plist member rather than offset. Handle
MIPS16/microMIPS PLT entries. Handle microMIPS stubs.
(_bfd_mips_vxworks_finish_dynamic_symbol): Update to use
gotplt_union's plist member rather than offset. Use
MIPS_ELF_GOT_SIZE to calculate GOT address.
(mips_finish_exec_plt): Handle microMIPS PLT. Return status.
(_bfd_mips_elf_finish_dynamic_sections): Handle result from
mips_finish_exec_plt.
(_bfd_mips_elf_link_hash_table_create): Update to use
gotplt_union's plist member rather than offset.
(_bfd_mips_elf_get_synthetic_symtab): New function.
include/elf/
* mips.h (ELF_ST_IS_MIPS_PLT): Respect STO_MIPS16 setting.
(ELF_ST_SET_MIPS_PLT): Likewise.
gdb/
* mips-tdep.c (mips_elf_make_msymbol_special): Handle MIPS16 and
microMIPS synthetic symbols.
ld/
* emulparams/elf32btsmip.sh: Arrange for .got.plt to be placed
as close to .plt as possible.
* scripttempl/elf.sc: Handle $INITIAL_READWRITE_SECTIONS and
$PLT_NEXT_DATA variables.
ld/testsuite/
* ld-mips-elf/jalx-2.dd: Update for microMIPS PLT support.
* ld-mips-elf/pic-and-nonpic-3a.dd: Update for the _MIPS_STUBS_
magic symbol.
* ld-mips-elf/pic-and-nonpic-3b.dd: Likewise.
* ld-mips-elf/pic-and-nonpic-6-n32.dd: Likewise.
* ld-mips-elf/pic-and-nonpic-6-n64.dd: Likewise.
* ld-mips-elf/pic-and-nonpic-6-o32.dd: Likewise.
* ld-mips-elf/stub-dynsym-1-10000.d: Likewise.
* ld-mips-elf/stub-dynsym-1-2fe80.d: Likewise.
* ld-mips-elf/stub-dynsym-1-7fff.d: Likewise.
* ld-mips-elf/stub-dynsym-1-8000.d: Likewise.
* ld-mips-elf/stub-dynsym-1-fff0.d: Likewise.
* ld-mips-elf/tlslib-o32.d: Likewise.
opcodes/
* mips-dis.c (is_mips16_plt_tail): New function.
(print_insn_mips16): Handle MIPS16 PLT entry's GOT slot address
word.
(is_compressed_mode_p): Handle MIPS16/microMIPS PLT entries.
Import the latest version of strlen from the Linaro cortex-strings
package. This version is faster across a variety of block size and
alignments on ARMv7.
newlib/ChangeLog:
2013-06-21 Will Newton <will.newton@linaro.org>
* libc/machine/arm/strlen-armv7.S: Import latest strlen
code from Linaro cortex-strings.
Tristan Gingold